This really needs to be done for a GLP-1 auto injecting needle.
Pretty sure it’s the same as an epi-pen as well.
It blows my mind. It’s a disposable, single use device that at the press of button:
1. Inserts the needle in your skin,
2. Slowly presses the plunger until the dose is injected
3. Then retracts the needle with plunger
Three distinct and seemingly opposing motions. With timing. All in a little plastic enclosure. It sure I can think of a toy with that kind of mechanism.
There's an even fancier mechanism with e.g. glucagon pens, where it actually has to rehydrate the freeze dried hormone (glucagon forms aggregations when it sits, has to be mixed fresh)
Actually, after looking into it recently, this is actually not true any more. All the current glucagon delivery mechanisms are either dry powder or DMSO-based, so no actual water involved, and are premixed and ready to go basically the same as epipen style autoinjectors
I'm excited for the advent of dasiglucagon which is a non-clumping peptide designed for the purpose.
When I was a kid I needed growth hormone shots. we used regular syringes that fit into this tan plastic "gun" thing. you pulled back the top into a locked position. placed the tip of the gun to the skin where the needle should inject, and pressed the trigger button to release the lock. can't remember if it also pushed the plunger though. this was back in the 90's.
Oh, is that why when you "overwound" it it would make that rapid ticking sound? The outer end of the spring is falling into the next little slot, huh. Fascinating stuff.
We had these for my boys. The target age range of someone who can have fun with these ends at about the same age you learn to be careful enough not to break the motor.
What is the name for the sort of toy car you push in one direction and it continues slowly in that direction? These ones were usually styled as 4x4 vehicles and almost moved like a rock crawler with the 4wd set to low. They could be pushed forward or in reverse (and then would go in reverse).
I learned this when I was 4. We even had ones that shot sparks. America. The animations on this are really well done and I loved that trip back to childhood of pulling the car back and letting it rip. However, given the popularity, you should simulate what happens when you pull it back to the extremes over and over again and the spring gets stretched. It no longer kicks as fast as it used to and in some cases, it won't go at all.
I guess as a kid I only had access to the cheap ones? Would pull back, not knowing where to stop, and there was eventually a crunching noise. Then I'd worry I'd ruined the thing!
yes this print is great, I was very surprised by the performance of the 3d printed spring. I did end up putting rubber bands on the rear wheels to give them more grip.
Wow. I love being reminded of stuff like this. Those cars were so cool.
Edit: I took one of these cars apart as a kid to see how it worked. This site brought back a lot of memories. The little coil spring inside the gear. I have to get my hands on one of these now…
The original 80s Darda cars were great fun, with enough power to get around great big loops. One of those childhood toys I wish I'd took more care of and kept hold of...
They did still produce a version relatively recently (looks like they're discontinued entirely now?), but the cars were significantly lighter and less powerful, all-plastic where the originals had metal bodies
I bought a Honda Civic toy from an auto parts store recently. I thought it was purely static but it has a spring pull back motion and also flashes the lights and honks the horn when you open the doors.
Then I leaned on it and discovered it makes a starting noise and vrooms the engine.
This really needs to be done for a GLP-1 auto injecting needle.
Pretty sure it’s the same as an epi-pen as well.
It blows my mind. It’s a disposable, single use device that at the press of button:
1. Inserts the needle in your skin, 2. Slowly presses the plunger until the dose is injected 3. Then retracts the needle with plunger
Three distinct and seemingly opposing motions. With timing. All in a little plastic enclosure. It sure I can think of a toy with that kind of mechanism.
Check out this video from Steve Mould; I think it covers exactly what you're looking for!
https://youtu.be/CfhsW1kaa2Q?is=ug5_Ze2HczVMGTMR
Untracked link: https://www.youtube.com/watch?v=CfhsW1kaa2Q
(It's a really good video btw!)
There's an even fancier mechanism with e.g. glucagon pens, where it actually has to rehydrate the freeze dried hormone (glucagon forms aggregations when it sits, has to be mixed fresh)
Actually, after looking into it recently, this is actually not true any more. All the current glucagon delivery mechanisms are either dry powder or DMSO-based, so no actual water involved, and are premixed and ready to go basically the same as epipen style autoinjectors
I'm excited for the advent of dasiglucagon which is a non-clumping peptide designed for the purpose.
When I was a kid I needed growth hormone shots. we used regular syringes that fit into this tan plastic "gun" thing. you pulled back the top into a locked position. placed the tip of the gun to the skin where the needle should inject, and pressed the trigger button to release the lock. can't remember if it also pushed the plunger though. this was back in the 90's.
Steve Mould has a great video explaining the mechanism in epi pens
Oh, is that why when you "overwound" it it would make that rapid ticking sound? The outer end of the spring is falling into the next little slot, huh. Fascinating stuff.
We had these for my boys. The target age range of someone who can have fun with these ends at about the same age you learn to be careful enough not to break the motor.
What is the name for the sort of toy car you push in one direction and it continues slowly in that direction? These ones were usually styled as 4x4 vehicles and almost moved like a rock crawler with the 4wd set to low. They could be pushed forward or in reverse (and then would go in reverse).
Are you talking about https://en.wikipedia.org/wiki/Friction_motor?
That's it.
Friction or flywheel car.
https://en.wikipedia.org/wiki/Friction_motor
This doesn't answer the most burning question I have, which is why the wind-up gear has the spiral around the shaft...
I learned this when I was 4. We even had ones that shot sparks. America. The animations on this are really well done and I loved that trip back to childhood of pulling the car back and letting it rip. However, given the popularity, you should simulate what happens when you pull it back to the extremes over and over again and the spring gets stretched. It no longer kicks as fast as it used to and in some cases, it won't go at all.
I guess as a kid I only had access to the cheap ones? Would pull back, not knowing where to stop, and there was eventually a crunching noise. Then I'd worry I'd ruined the thing!
The "mystery" posed at the end of the OP suggests that that crunching noise was the action of the built-in strain relief within the spring enclosure.
I really love this site, it is obivous that the owner puts a lot of effort into this
Much like https://ciechanow.ski/
If you have access to a 3D printer, this helps explain the basics too: https://www.thingiverse.com/thing:3308710
yes this print is great, I was very surprised by the performance of the 3d printed spring. I did end up putting rubber bands on the rear wheels to give them more grip.
Wow. I love being reminded of stuff like this. Those cars were so cool.
Edit: I took one of these cars apart as a kid to see how it worked. This site brought back a lot of memories. The little coil spring inside the gear. I have to get my hands on one of these now…
The original 80s Darda cars were great fun, with enough power to get around great big loops. One of those childhood toys I wish I'd took more care of and kept hold of...
They did still produce a version relatively recently (looks like they're discontinued entirely now?), but the cars were significantly lighter and less powerful, all-plastic where the originals had metal bodies
I bought a Honda Civic toy from an auto parts store recently. I thought it was purely static but it has a spring pull back motion and also flashes the lights and honks the horn when you open the doors.
Then I leaned on it and discovered it makes a starting noise and vrooms the engine.
I felt like I was 10 years old again.
Why is the wind-up gear needed? Couldn't the axle be connected directly to the spring gear?
Love this site! Well done!
absolutely love it! Gorgeous drawing, meticulous detail.
Great site!
Please leave my browser history alone
what does this mean ? whats the context ?